TI-HP1 High Performance Ultrasonic Wall Thickness Gauge

TI-HP1 Measuring Range 0.010 - 480 inches 0.63 - 12 meters

The new CHECK-LINE TI-HP1 Ultrasonic Thickness Gauge accurately measures the most difficult materials, such as rubber - from only one side!

The TI-HP1 is a full-function, A-Scan thickness gauge with a wide variety of modes and features for extra versatility. The A-Scan display options and dual gates enable the TI-HP1 to be optimized for multi-mode through paint requirements.

The TI-HP1 is shipped with software for transferring data to and from a PC. Software is compatible with Windows 95/98/NT.

For more detailed thickness analysis,
an A-Scan mode can be used.

Gauge configuration and calibration is done via plain English menus.

Twenty-five manufacturer defined setups that can be modified by the user to create customer setups for specific applications

Alphanumeric data logger stores up to 1000 pages of data and A-Scans

Portable, battery powered as well as AC powered

User Selected English/Metric units

Lock-out capability disables the A-Scan features and allows the TI-HP1 to be used as a  simple digital thickness gauge.

Two-year warranty. Free NIST Certification included

4 Step Steel Test Block

Precision Machined and Finished
Includes NIST Report and Test Data
Wooden Storage Box Optional

Click here for more information

Measuring

Range: Measures from 0.010 to 480 inches (0.63 to 12 Meters) in steel. Switch to select english or metric units.

Resolution:
Standard Mode - .001 inches (0.01 mm)
High Resolution Mode - .0001 inches (0.001 mm)

Velocity Range:
.0500 to .3937 in/ms (1270 to 10,000 meters/sec)

Selectable pulse repetition rate allows for high speed scanning or low power operation.

Single and Two point calibration capability.

Ultrasonic Specifications

Measurement Modes:
Pulse-Echo (flaws, pits) Echo-Echo (thru paint, precision delay line)

Pulser:
Tone-burst (push-pull). Selectable 1, 2 or 4 pulses. Selectable frequencies (MHz): 0.5, 1, 2.25, 5, Hi Freq.

Receiver:
Low noise pre-amplifier.
Adjustable gain control.

Timing:
160 MHz 10 ppm TCXO controlled digitizer.

Memory:
8 megabit non-volatile ram.

Power Source

Four 1.5V alkaline or 1.2V NiCad C cells 100-240 VAC input 12VDC power supply

Typically operates for 30 hours on alkaline and 15 hours on NiCad

Physical

Size:
8.5 in (W) x 6.5 in. (H) x 2.0 in (D) 216 mm x 165 x 51 mm

Weight:
2lbs. 10 ounces (1.2 Kg)

Keyboard:
Membrane pad with tactile keys.

Operating Temperature:
-4° to 122° F(-20° to 50° C)

Case:
Extruded aluminum body with nickel-plated aluminum end caps (gasket sealed).

Data Output:
RS232 port out Windows interface software.

Display:
Backlit LCD-3.5"W x 2.0"H

Display

Display Views:
Rectified (flaw view)
RF (full waveform view)
Digital thickness readout

Multi-function 6 digit graphic LCD, backlit for use in poor light conditions.

Measurements displayed in inches, inches/microsecond.

Bar graph indicates stability of reading.

Data Logger (internal):

1000 pages of memory (alpha numeric storage)-I main cell reading, 1 waveform, 2 comment lines, and 16 sub readings per page. OBSTRUCT for indicating inaccessible locations.

Transducer

Transducer Types Dual Element (1 to 10 MHZ) Single Element Contact (500 KHz to 10 MHz) Single Element Delay Line (5 to 22 MHz)

Locking quick disconnect "00" LEMO connectors.

Standard 4 foot cable.

Custom transducers and length cables available for special applications