link to Home Page	Newman Tools Inc.     Tel 1-800-465-1384     Fax 1-800-605-2442
	..."IN STOCK"... vast selection, over 30,000 different items including, "hard-to-find/special sizes"		Fast Jump on the Newman Tools' site Go to ... Home Page Brand Name index Product list Technical info Price list Monthly specials $$$$ Jokes Latest page additions Contact Information Email the Boss

Dumore Drill Accessories

	DRILL ACCESSORIES
	Tapping Control Panel Automation Control Foot Switch Filter/Oiler/Regulator Timed Deep Hole Drilling Attachment Pressure Sensitive Deep Hole Drilling Attachment Non-Reversing Drilling Motors Reversing Drill and Tap Motor Hydraulic Feed Control Timing Belt Pulleys
	Tapping Control Panel
	Used with 28-010 Drill Unit and 28-152 Reversing Motor. Reversing magnetic contactors reverse 28-152 motor at the end of tapping stroke for tap withdrawal when in "TAP" position. Switch has "TAP", "DRILL", and "OFF" positions. Also serves as motor starter in both "TAP" and "DRILL" positions. No. 28-200
	Automation Control
	Converts a sustained electrical signal (from work-holding devices, index tables, other units, etc.) to a momentary electrical signal needed to actuate drill or tap units. Simplifies interface with automated equipment. Optional on Series 28. No. 24-232
	Foot Switch Optional on Series 28. No. 24-240
	Filter/Oiler/Regulator
	Assembly installed in air line removes impurities, injects oil vapor into system and allows operator to adjust air pressure to deliver required thrust to drill unit. No. 60-300
	Timed Deep Hole Drilling Attachment
	Allows unit to peck drill at timed intervals to remove chips and admit coolant. Timer controls both advance (ON) time and retract (OFF) time. Strokes are timed from the moment of drill advance and drill retraction. Advance (ON) time includes actual drill time and idle endurance time to the work. Unit plugs into side panel, and can handle up to 8 units. Optional on Series 28 unit. No. 24-230
	Pressure Sensitive Deep Hole Drilling Attachment
	Advised for small diameter, deep holes where peck drilling is required. Pressure sensitive, timing begins when drill actually begins to remove stock. At the end of the pre-set time interval the unit retracts, removing chips and allowing coolant to enter. Plugs into side panel. Optional on Series 28 unit. No. 24-233
	Non-Reversing Drilling Motors
	3/4 HP, totally enclosed, non-reversing induction motors provide spindle drive for Series 22 and 28 Drill Units. Used for drilling only. Available in single phase, 115/230V, w/ 8' cord and 3-prong plug, or 3 phase, 220/440V, less cord and plug. Weight: Net 33 lbs., Shipping 35 lbs. No. 24-151(Single Phase) No. 24-152(3 phase)
	Reversing Drill and Tap Motor
	Heavy-duty 1 HP, 220/440V, 60 Hz, 3 Phase, TEFC reversing induction motor provides up to 16 reversals per minute for production tapping. Can also be used for drilling. Weight: Net 46 lbs., Shipping 49 lbs. No. 28-152
	Hydraulic Feed Control
	Speeds the entire drilling cycle, and increases productivity by allowing the drill to rapidly approach the workpiece. It accurately controls the feed rate for small hole drilling and minimizes burrs on breakthrough holes. Recommended when drilling hard material, spot facing, boring, angular drilling, curved surface breakthrough. Optional on Series 22 and 28. No. 24-111
	Timing Belt Pulleys
	Plastic with splined steel inserts. Pulleys optional on Series 22. Order by number. Each is a set of two except No. 22-107 kit of all 8 pulleys. 400 and 7420 RPM No. 22-102 560 and 5300 RPM No. 22-103 765 and 3880 RPM No. 22-104 1055 and 2825 RPM No. 22-105 1430 and 2085 RPM No. 22-106 Complete Set No. 22-107

Back to Top of Page

 link to product table of contents       link to what's "NEW"        link to price list

Please send comments, questions, email to   tom@newmantools.com    ( this email will be returned advising you to resend the email to the following email address )

spamfilter "at" newmantools "dot" com. This notation is to prevent the robots from harvesting this email address.

return to Newman Tools Home Page.

and the states of Alabama, Alaska, Arizona, Arkansas, California, Colorado, Connecticut, Delaware, Florida, Georgia, Hawaii, Idaho, Illinois, Indiana, Iowa, Kansas, Kentucky, Louisiana, Maine, Maryland, Massachusetts, Michigan, Minnesota, Mississippi, Missouri, Montana, Nebraska, Nevada, New Hampshire, New Jersey, New Mexico, New York, North Carolina, North Dakota, Ohio, Oklahoma, Oregon, Pennsylvania, Rhode Island, South Carolina, South Dakota, Tennessee, Texas, Utah, Vermont, Virginia, Washington, West Virginia, Wisconsin,Wyoming

Newman Tools Inc.October 2001
Newman Tools Inc.