PRODUCT DESCRIPTION N-5000 is a nickel-based anti-seize lubricant, produced under 100% controlled conditions for highest purity. It is formulated to have the lowest practical levels of halogens, sulfur and heavy metals, including copper. N-5000 has a general composition of nickel and graphite flake in petroleum carrier. All ingredients are selected for extreme purity. Special Features: · High purity - made from highest purity ingredients · Trace amount of copper - less than 50 ppm copper · Typically used in applications with a dry surface temperature of -29 to +1315ºC (-20 to +2400ºF)
TYPICAL APPLICATIONS · Bolts, studs, valves, pipe fittings, slip fits and press fits in nuclear electric power generating plants, chemical plants, pharmaceutical plants, paper mills and other locations where stainless steel fasteners are used. Operational Benefits: · During assembly - prevents high friction, galling and seizing. · Promotes uniform and predictable clamping. · During operation - high purity prevents stress corrosion · Disassembly - prevents seizing, galling, destruction of threads
DIRECTIONS FOR USE 1. Before or during assembly, wipe brush onto threads and other joint surfaces needing protection. 2. Use full strength. Do not thin.
TYPICAL PURITY Impurities-Combined Test ASTM No. Controlled Typical & Uncombined Method or (SM16) Max. Value Halogen,Chlorine, Bromine, Iodine Parr Bomb, Turbidimetric D808-87, C69979 50 ppm 11 ppm Fluorine Parr Bomb, Specific ION Electrode D3761-84 200 ppm 7 ppm Sulfur Parr Bomb, Turbidimetric D129-64, D1266-87 100 ppm 9 ppm Lead Wet Digestion, AAS (302D), D3559-84 25 ppm 1 ppm Cadmium Wet Digestion, AAS (302D), D3557-84 2 ppm .2 ppm Tin Wet Digestion, AAS (302D), E37-76 25 ppm 9 ppm Zinc Wet Digestion, AAS (302D), D1691-84 25 ppm 1 ppm Copper Wet Digestion, AAS (302D), D1688-94 50 ppm 2 ppm Mercury Wet Digestion, Cold Vapor, AAS (302D), D3223-80 2 ppm .04ppm
PROPERTIES OF MATERIAL Typical Value Appearance Silver-grey paste Weight per Gallon, lbs. 9.5 - 10.4 Specific Gravity 1.14 - 1.25 Penetration, ASTM D 217-88 unworked, mm 330 - 380
TYPICAL PERFORMANCE An anti-seize lubricant used on a bolt helps to develop greater clamp load for the same torque compared to an unlubricated bolt. An additional benefit is greater uniformity in clamp load among a series of bolts. The relationship between torque and clamp load is expressed in the following equation: T = K x F x D · T = Torque (in-lb, ft-lb, N-m) · K = Torque coefficient or nut factor · F = Clamp Load (lb, N) · D = Nominal diameter of bolt (in, ft, m), determined experimentally. K Factor: K factors are obtained on Grade 8, 1/2” steel bolts and Grade 5 nuts by a test procedure which measures torque tension properties. Lubricant was applied to the bolt threads and both faces of the washer. See properties chart for the torque coefficient or K value for the anti-seize compounds. We feel that this data fairly represents performance to be expected. However, the manufacturer makes no warranty of specific performance on any individual fastener. In critical applications, it is necessary to determine K values independently. Properties Typical Value Torque coefficient, k on steel nuts and bolts .15 Type 304 stainless steel .18 Torque coefficient, k (solvent cleaned, not lubricated) .27
GENERAL INFORMATION This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS). Ordering Information Part Number Container Size 51346 1 oz. Tube 51243 8 oz. Brush Top Can 51245 8 lb. Can 51246 2 lb. Can 51269 1 lb. Brush Top Can
Storage Product shall be ideally stored in a cool, dry location in unopened containers at a temperature between 8°C to 28°C (46°F to 82°F) unless otherwise labeled. Optimal storage is at the lower half of this temperature range. To prevent contamination of unused product, do not return any material to its original container. For further specific shelf life information, contact your local Technical Service Center.
Data Ranges The data contained herein may be reported as a typical value and/or range. Values are based on actual test data and are verified on a periodic basis.
Back to Top of Page link to product table of contents link to what's "NEW" link to price list
FastCounter by LinkExchange
Please send comments, questions, email tomailto:tom@newmantools.com
return to Newman Tools Home Page.