link to Home Page Logo, Link to Home Page Newman Tools Inc.     Tel 1-800-465-1384     Fax 1-800-605-2442
..."IN STOCK"... vast selection, over 30,000 different items including,
"hard-to-find/special sizes"
        Fast Jump on the Newman Tools' site

30,000 items In Stock... hard to find / special sizes

Highlights made by KNIPEX

Cobra Water Pump Plier | Ultra High Leverage End Cutter | Plier Wrench |
Self-Adjusting Crimping Tools for wire end ferrules | High Leverage Concretors Nipper |
Dual Cutting Edge Cable Shears | CoBolt Lever Action Center Cutter


horz. bar


cobra Cobra Water Pump Plier: Water Pump and Locking Pliers plus Pipe Wrench in one tool. This unique tool provides instant adjustment, memory retention of jaw opening and single handed, self gripping operation with a grip that wont' let go. cobraThe Cobra is designed to eliminate "nuckle-busting" and the "burring" of nuts, bolts and fittings. Its light weight and thin profile ensure ease of operation.


Ultra High Leverage End Cutter Ultra High Leverage End Cutter: KNIPEX Ultra High Leverage End Cutter is a high performance tool that will outperform most larger end cutters. The high leverage design provides exceptional cutting of hard and soft wire, bolts, nails, rivets, pins, etc. The fatigue reducing ergonomic design produces high cutting efficiency with minimal effort. The cutter is forged from high grade, oil-hardened steel for maximum strength, ruggedness and minimum weight. The precision cutting edges are induction hardened to approximately 64 HRC for long service life. Ultra High Leverage End Cutter


 

Plier Wrench Plier Wrench:
A superior tool for gripping, holding and bending. Nuts and unions of all sizes up to 35 mm / 1 3/8" (86 03 180), 46 mm / 1 ¾" (86 03 250) and 60 mm / 2 3/8" (86 03 300) across flats can be tightened and released with the parallel gripping jaws. The cam action on the jaws allows ratchet action to operate over the hole range. The smooth parallel jaws avoid damage to plated and soft fittings. The lever ratio is greater than 10 - 1 for strong gripping power.
 
herkömmlicher Schraubenschlüssel Tension curves when force is applied on a conventional wrench (at the top) and the Knipex Plier Wrench (at the bottom).



 
Knipex Zangenschlüssel



Self-Adjusting Crimping Tools for wire end ferrules:
The unique, self-adjusting crimping profile allows reliable and easy crimping for ferrulescrimpen ohne probleme for stranded wire from 0.08 - 6 mm², 28 -10 AWG (97 53 04) resp. 0.75 - 10 mm², 18 - 7 AWG 97 53 05). The square crimping profile guarantees a very favourable contact area on the connector. The release mechanism will allow the jaws to open only after the full crimping cycle has been completed.
Ergonomically designed hand grips and an optimum lever action offer an easy, fatigue reducing operation.
Crimpzange

Crimpprofil

 



High Leverage Concretors Nipper
High Leverage Concretors Nipper
High Leverage Concretors Nipper: The high leverage concretors nipper has been developed from research into the use in structural and civil engineering as well as in the mass production of pre-cast concrete. This tool has a considerably higher cutting efficiency when compared with the traditional concretors nippers as well as a strong reduction in cutting "shock" in the hand - two valuable ergonomic advantages for the user.
Twisted binding wire of 2 x 2 mm dia. (= 4 mm) can be cut easily. The maximum capacity (for soft wire) is 5 mm dia. The slim design and longer length facilitate the use in confined spaces.


Dual Cutting Edge Cable Shears: When talking about cable shears usually the problem is the opening width of the handles when cutting. It is difficult to produce force with splayed out fingers. The KNIPEX cable shears offer a clear advantage: the dual cutting edge principle allows for the insulation to be cut using the front cutting edge (favourable handle position in spite of larger opening), while the conductor itself is cut using the second cutting edge close to the joint, thus benefiting from the higher lever ratio. The tool is designed for fast clean cutting of copper / aluminium cable only and has sharp hardened precision ground cutting edges. The joint screw is adjustable.
 
cable shear
initial cut  

Phase 1:

Initial cut

     
final cut  

Phase 2:

Final cut

favourable hand position



CoBolt Lever Action Center Cutter:
CoBolt

CoBolt in action

The KNIPEX Lever Action Center Cutter is a light-weight and very handy tool that cuts even the hardest material with little effort. The cutting strength at the cutting edges is more than twenty times higher than the used hand force. This is achieved by a newly developed transmission system, which guarantees an extremely good lever action ratio reducing friction at the same time. A compact, extremely efficient tool to be used even under tightest working conditions.


Back to Top of Page
horz. bar
 link to product table of contents       link to what's "NEW"        link to price list



Newman Tools Logo


Newman Tools Inc.
3422 Notre Dame West
Montreal, Quebec, Canada H4C 1P2
Phone: 1-514-931-2472 or 1-800-465-1384
Fax:1-514-931-6193 or 1-800-605-2442


Newman Tools Inc.
185 Iber Road
Stittsville, Ottawa, Ontario K2S 1E7
Phone: 1-800-465-1384
Fax: 1-800-605-2442

Newman Tools Inc.
151 New Park Avenue
Hartford, CT 06106, USA
Phone: 1-800-465-1384
Fax: 1-800-605-2442


E-mail: info@newmantools.com



FastCounter by LinkExchange

Please send comments, questions, email to webmaster@newmantools.com

return to Newman Tools Home Page.


Go to ... Home Page  | Brand Name index  | Product list  | Technical info  | Price list  | Monthly specials $$$$  | Jokes  | Latest page additions  | Contact Information  | Email the Boss

June 2001
Newman Tools Inc.