Lindapter Product Range - Recessed Type D2

link to Home Page Logo, Link to Home Page Newman Tools Inc. Tel 1-800-465-1384 Fax 1-800-605-2442

..."IN STOCK"... vast selection, over 30,000 different items including,
"hard-to-find/special sizes"
Fast Jump on the Newman Tools' site

link to Lindapter index page

30,000 items In Stock... hard to find / special sizes

Recessed Type D2

The addition of a tail-screw allows the Type D2 to accommodate a wide range of flanges without the use of packings (see table below). Above these limits Type P Long Packings can be used. The recess accepts standard hexagon bolts only.

Finish: Electro-Galvanised.

Ref : 10012

Dimensions

Product Code Bolt Size
Z
(inches) Y X V V1 S T Body Width Minimum
flange
thickness
with
inverted
setscrew
(inches)

LD2037 3/8 25/32 25/32 3/4 1/4 3/16 3/16 1 1/32 3/16

LD2050 1/2 1 1/32 1 7/8 1/4 1/4 1/4 1 1/8 3/16

LD2062 5/8 1 3/16 1 3/16 1 3/16 3/8 5/16 5/16 1 3/8 1/4

LD2075 3/4 1 7/16 1 3/8 1 8/16 3/8 3/8 1 21/32 11/32

LD2100 1 1 7/8 1 15/16 1 3/16 3/4 1/2 1/2 2 1/8 3/8

Loadings for SAE Bolt Grade 2

Product Code Bolt Size
Z
(inches) Tensile § (lb)
(per single bolt) Frictional § (lb)
steelwork painted,
Lindapter galvanised,
(per 2 bolts) Torque (lb ft)

LD2037 3/8 330 - 15

LD2050 1/2 830 135 28

LD2062 5/8 1160 157 68

LD2075 3/4 1930 337 130

LD2100 1 2900 450 173

Loadings for SAE Bolt Grade 5

Product Code Bolt Size
Z
(inches) Tensile § (lb)
(per single bolt) Frictional § (lb)
steelwork painted,
Lindapter galvanised,
(per 2 bolts) Torque (lb ft)

LD2037 3/8 - - -

LD2050 1/2 1300 157 50

LD2062 5/8 1640 337 108

LD2075 3/4 3300 674 210

LD2100 1 4429 1012 362

§ Special conditions may apply. See Loads and Specifications.

All loads are based on the recommended Safety Factor of 5.

Use of any lower Safety Factor is at the customer's discretion.

Suitable for both parallel and sloping flanges up to 4°.

For applications on steelwork with sloping flanges above 4°, see Type LR and Type BR.

Also see tail-length / packing combinations.

On thin flanges it is necessary to invert the tail adjustment setscrew.

Note: The tail-screw must be set to 1/16" less than the length required before tightening the bolt. The top edge of the D2 should be at approx 90° to the bolt shank.

Back to Top of Page

horz. bar

link to product table of contents link to what's "NEW" link to price list

Newman Tools Logo

Newman Tools Inc.
185 Iber Road
Stittsville, Ottawa, Ontario, Canada K2S 1E7
Phone: 1-613-836- 6776 or 1-800-465-1384
Fax: 1-613 -836 -9070 or 1-800-605-2442

Newman Tools Inc.
151 New Park Avenue
Hartford, CT 06106, USA
Phone: 1-800-465-1384
Fax: 1-800-605-2442

Email: info@newmantools.com

Please send comments, questions, email to tom@newmantools.com ( this email will be returned advising you to resend the email to the following email address )

spamfilter1 "at" newmantools "dot" com. This notation is to prevent the robots from harvesting this email address.

return to Newman Tools Home Page.

Servicing the Canadian provinces of Newfoundland, Nova Scotia, New Brunswick, Prince Edward Island, Quebec, Ontario, Manitoba, Saskatchewan, Alberta ,British Columbia and the states of Alabama, Alaska, Arizona, Arkansas, California, Colorado, Connecticut, Delaware, Florida, Georgia, Hawaii, Idaho, Illinois, Indiana, Iowa, Kansas, Kentucky, Louisiana, Maine, Maryland, Massachusetts, Michigan, Minnesota, Mississippi, Missouri, Montana, Nebraska, Nevada, New Hampshire, New Jersey, New Mexico, New York, North Carolina, North Dakota, Ohio, Oklahoma, Oregon, Pennsylvania, Rhode Island, South Carolina, South Dakota, Tennessee, Texas, Utah, Vermont, Virginia, Washington, West Virginia, Wisconsin,Wyoming

August 2000
Newman Tools Inc.

Newman Tools Inc. makes every effort to ensure technical specifications and other descriptions are correct. Responsibility for errors or omissions cannot be accepted. We reserve the right to make specification changes without prior notice.

Lindapter® is a registered trademark of Lindapter International